sportsiorew.blogg.se

Svp mpc software#
Svp mpc Pc#
Svp mpc windows 7#

Select a UTC timezone from the drop-down list, and then click NoteSet the SVP date, time, and time zone according to the local time of the location of the installed SVP. The following figure shows a CBLM and CBLH storage system in a non-bridged environment. The following figure shows a CBSS and CBSL storage system in a non-bridged environment. Remove the Ethernet cables from SVP ports LAN3 and LAN4, and attach them to the Ethernet switches. Right-click the network bridge icon, and then click If prompted that the identity of the remote computer cannot be verified, clickĬontrol Panel Network and Sharing Center.

Svp mpc Pc#

Log on to the SVP using the Remote Desktop Connection:Ĭonfigure the PC to use an IP address of 10.0.0.xxx, where xxx = 1-99 or 101-254, and a subnet mask of 255.255.255.0. Repeat steps 1 through 3 for the other outer rail.Ĭonnect a PC to the LAN2 port on the SVP. Then connect the short outer rail to the vertical rail at the rear of the rack using another washer and M5 screw. Secure the long outer rail to the vertical rail at the front of the rack using a washer and an M5 screw on one side of the rail and a safety nut on the other side. Then insert two small screws and two large M5 screws into the threaded holes in the slide area on the rails, as shown in the following figure, to prevent the rails from moving. Adjust both the short rail and long rail to the proper distance, so that they fit snugly into the rack. Using the directions on the rails, orient the rails so that the front of the rail faces the front of the rack. If you need to disconnect the management console from the physical SVP, use the following procedure.Īttach the short bracket to the outside of the long bracket.

Disconnecting the management console from the physical SVP.

Svp mpc windows 7#

You specify these settings using the Windows 7 operating system running on the SVP, and then specify the same settings in the maintenance utility. Use the management console PC to set the SVP date, time, and time zone according to the local time of the location of the installed SVP.

Setting the SVP date, time, and time zone settings.

This configuration disables the SVP's internal bridge, and allows you to connect the Ethernet cables to Ethernet switches instead of SVP ports LAN3 and LAN4.

Use the non-bridged configuration if BDPU guard is enabled in your networking environment.

Operating the physical SVP in a non-bridged network configurationĪfter you make the physical connections to the Hitachi-supplied SVP, apply power, and run the initial setup, you can configure the physical SVP to operate in a non-bridged network configuration.

Do not use a power cable designed for another device. When turning on the power to the physical SVP, use only the power cable supplied with the SVP.

Installing the physical SVP into the rackĪfter the inner and outer rails are attached to the physical SVP, the SVP can be installed in a rack.Īll port connections to the physical SVP are located at the rear of the SVP.

The outer rails that secure the physical SVP directly to the rack. Each assembly consists of an inner fixed chassis rail that secures directly to the SVP chassis, and an outer fixed rack rail that secures directly to the rack itself. The physical SVP contains two rack rail assemblies. Mounting the physical SVP appropriately in the rack is critical to ensure optimum performance. The 4U CBL controller and dense intermix drive tray (DB60) have a depth of 34.1 inches (865 mm) and 33.9 inches (860 mm), respectively. The physical SVP has a depth of 14.5 inches (369 mm). To enable IPMI LAN, change the BMC network configuration on the BIOS menu from "Update IPMI LAN configuration"="No" to "Yes" and perform the appropriate IP address setting. IST uses LAN1/3/4 or 2 ports for Remote Desktop Protocol (RDP). The user connects to the SVP using the IP address 192.168.0.15 for LAN1/3/4 ports (management) or 10.0.0.100 for LAN2 port (maintenance), respectively. Do not operate the SVP at temperatures of 104☏ (40☌) or higher. The physical SVP is not supported in high-temperature environments. This arrangement obviates the need for an external switching hub. For the physical SVP, a network bridge configures the four local-area network (LAN) ports on the SVP using the Bridge Connections setting in the Windows operating system.

Svp mpc software#

Network bridge is software or hardware that connects two or more networks so that they can communicate. The SVP runs the Windows Embedded Standard 7 operating system, and is installed above the controller and drive trays in the rack. The SVP provides out‑of‑band configuration and management of the storage system, and collects performance data for key components to enable diagnostic testing and analysis. The SVP operates independently from the storage system's CPU and operating system. Hitachi Vantara provides a 1U SVP for use with the